How can I get a screw like this out?

Submitted ⁨⁨3⁩ ⁨months⁩ ago⁩ by ⁨fernlike3923@sh.itjust.works⁩ to ⁨[deleted]⁩

https://sh.itjust.works/pictrs/image/b3f22381-7282-4cc8-916d-b54efeb2d101.jpeg

I decided on cleaning my laptop fans today, which I’ve been procrastinating for about a year now because of this one screw. But I just can’t seem to open this with my screwdriver, since whatever I did back when I last opened it it’s nearly circular now. Is there a way to unscrew this?

source

Comments

Sort:hotnew top

DaddleDew@lemmy.world ⁨3⁩ ⁨months⁩ ago
Carefully dremel a slot and use a flat head screwdriver.

source
FuglyDuck@lemmy.world ⁨3⁩ ⁨months⁩ ago
So if you have a dremel and steady hands, a cut off wheel can make your own slot for a straight Phillips.

Just be careful to not knick anything else. This is more of a last resort thing, but I’ve never had it not work.

source
- Warl0k3@lemmy.world ⁨3⁩ ⁨months⁩ ago
  Learn from my mistakes, mask off your laptop’s ports and vents before you do this
  
  source
  - FuglyDuck@lemmy.world ⁨3⁩ ⁨months⁩ ago
    Ooof. Not something I’d have thought of myself…
    
    Benefit of your hindsight it’s obvious… lol. How bad were the sparks?
    
    source
    -> View More Comments
  - trolololol@lemmy.world ⁨3⁩ ⁨months⁩ ago
    Keyboard too?
    
    source
    -> View More Comments
- ShepherdPie@midwest.social ⁨3⁩ ⁨months⁩ ago
  Flathead/standard not a straight Philips.
  
  source
  - eRac@lemmings.world ⁨3⁩ ⁨months⁩ ago
    Flathead is a description of the head profile, like panhead. Slotted is the screwdriver type that is just a single slot.
    
    source
    -> View More Comments
- Impromptu2599@lemmy.world ⁨3⁩ ⁨months⁩ ago
  I came here to say that
  
  source
ArbitraryValue@sh.itjust.works ⁨3⁩ ⁨months⁩ ago
They make screw extractor bits with thread that winds the opposite way from the screw itself so that the bit drills into the screw while turning counterclockwise, but I don’t think that’s worth bothering with here (and I’ve never seen an extractor this small.) Just drill the head off with a normal drill bit. The body will stay stuck in the hole, but you’ll be able to take the cover off and laptops are usually held together by so many screws that a missing one won’t cause problems.

source
Baphomet_The_Blasphemer@lemmy.world ⁨3⁩ ⁨months⁩ ago
Old life hack that occasionally works for this is to use a rubber band. Grab a rubber band wide enough to cover the screw head, push the screwdriver into the screw through the rubber band, and pray it has enough grip to twist the screw loose. Good luck with whatever method you use.

source
- Goodtoknow@lemmy.ca ⁨3⁩ ⁨months⁩ ago
  Never in the history has that worked for me of doing laptop repair professionally.
  
  source
  - setsneedtofeed@lemmy.world ⁨3⁩ ⁨months⁩ ago
    Thank you. This is always in the list of handyman hacks, and using a rubberband has never worked for me either. I’m convinced 90% of the people recommending it are just repeating what they’ve heard and haven’t actually tried it.
    
    source
    -> View More Comments
  - 13esq@lemmy.world ⁨3⁩ ⁨months⁩ ago
    It’s worked for me but with a couple layers of insulation tape rather than a rubber band.
    
    source
- ITGuyLevi@programming.dev ⁨3⁩ ⁨months⁩ ago
  Old Nintendo security screws were easily overcome by melting the end of a pen tube (the clear plastic Bic’s were always my preference), and jamming it in there holding it still while it cooled. Could work in this case.
  
  source
  - toynbee@lemmy.world ⁨3⁩ ⁨months⁩ ago
    I have successfully done this with a fuse box.
    
    source
MTK@lemmy.world ⁨3⁩ ⁨months⁩ ago
Try addinv a rubber band between the screw and the screwdriver, it adds friction which sometimes (usually not) helps

source
quixotic120@lemmy.world ⁨3⁩ ⁨months⁩ ago
Put a rubber band between screwdriver and screw, otherwise the other things already stated like CA glue, filing a flathead groove, or drilling the cap off

in the future use the appropriate sized driver and retire drivers when they become stripped

source
- j4k3@lemmy.world ⁨3⁩ ⁨months⁩ ago
  This. The rubber band trick works well for the first step. I came to say this.
  
  source
- tomcatt360@lemmy.zip ⁨3⁩ ⁨months⁩ ago
  Just so you know, OP, CA glue is a generic term for CyanoAcrylate glue, like Super Glue or Krazy Glue.
  
  Bring out the KraGle!
  
  source
- prime_number_314159@lemmy.world ⁨3⁩ ⁨months⁩ ago
  The rubber band trick is great, and very low effort/cost. I want to say, though, that it can take substantially more force than it looks like it should on small screws like this. You also don’t have to use something shaped for the original driver of the screw. With the rubber to help it, a round cylinder a little smaller than the head of the screw can work very well.
  
  source
DarkSurferZA@lemmy.world ⁨3⁩ ⁨months⁩ ago
If you have a Dremel, grind a slot into it and unscrew it.

If it has a hard backing, you can place a flat head screwdriver on it, give it a few taps, apply loads of pressure and turn it out.

If none of these are possible, a drop of CA adhesive on the screwdriver head, push it against the screw, make sure there is no excess leakage, then use a quick set spray. Once the screw has been turned out, use acetone to remove the glue.

If all of this fails, you gotta drill it. A hand crank drill, and a left handed bit. People seldom have these, so I assume this is your last resort.

Final bit of advice, hit the screw head a couple of times before you try any of these as it loosens the screw a tad. Also, sharpen an old screwdriver tip to just the width and thickness of what is left of the screw head slots.

Good luck.

source
- dual_sport_dork@lemmy.world ⁨3⁩ ⁨months⁩ ago
  
  If you have a Dremel, grind a slot into it and unscrew it.
  
  This has saved my ass many times. I keep one of those diamond coated wheels on a spare cutoff mandrel already mounted up pretty much specifically for this purpose.
  
  source
  - A_Union_of_Kobolds@lemmy.world ⁨3⁩ ⁨months⁩ ago
    I was gonna say, my Harbor Freight Dremel has been a fantastic use of a couple bucks. I get tons of use from it.
    
    source
- fernlike3923@sh.itjust.works ⁨3⁩ ⁨months⁩ ago
  Sadly no Dremel. I will try out a screw extractor and buy a few other screws before drilling or getting adhesive, thank you for your response!
  
  source
  - ShepherdPie@midwest.social ⁨3⁩ ⁨months⁩ ago
    Do you have a large Philips bit (like #3 or #4, the largest one that will fit in whats left of the screw)? You could try using that and tapping the end with a hammer (not too hard since its plastic) while gently twisting it. This usually shocks the screw and breaks it loose.
    
    source
gibmiser@lemmy.world ⁨3⁩ ⁨months⁩ ago
Take the drill bit out of your drill. Open the chuck up all the way and place it over the screw. If there is enough screw head there you might be able to grab it with the drill and just unscrew.

source
- CeruleanRuin@lemmings.world ⁨3⁩ ⁨months⁩ ago
  Cripes, it never even occurred to me that you could do this with a chuck. Thanks for expanding my mind.
  
  source
SharkEatingBreakfast@sopuli.xyz ⁨3⁩ ⁨months⁩ ago
Vampliers!

I work(ed) with old machines, and it was an absolute godsend. Prefer it after using penetrating spray on stuck screws.

source
- projectsquared@lemmy.world ⁨3⁩ ⁨months⁩ ago
  Those look very interesting. Thank you!
  
  source
MonkderVierte@lemmy.ml ⁨3⁩ ⁨months⁩ ago
Drill in it, put fitting star bit in hole, unscrew.

source
- Krzd@lemmy.world ⁨3⁩ ⁨months⁩ ago
  That usually works, however you need too much force to press the torx bit into the hole to do that on sensitive electronics. That screw is probably only threaded into plastic.
  
  source
  - lightnsfw@reddthat.com ⁨3⁩ ⁨months⁩ ago
    Looks like it sticks out a bit. Cut a slot in it and use a flathead.
    
    source
  - MonkderVierte@lemmy.ml ⁨3⁩ ⁨months⁩ ago
    Looks like sheet metal to me.
    
    source
TheChargedCreeper864@lemmy.ml ⁨3⁩ ⁨months⁩ ago
I once had a screw on a laptop that wouldn’t unscrew and eventually somewhat lost its shape. I had asked my uncle for help, who gave me the solution. I think it was slightly less bad than this, but it might help:

Apply WD40 around the edges of the screw, such that it could enter the hole

Apply it to the screw head

Hold your screwdriver in the hole and gently tap it with a hammer a couple of times

Slowly attempt to screw it out, whilst applying firm downward pressure on the screw

Note that the amounts of WD40 you have to apply are tiny. We’re talking drops of the stuff. It might be best to attempt to spray something else, and use the residue on the nozzle to apply it
source
Brkdncr@lemmy.world ⁨3⁩ ⁨months⁩ ago
Jb weld a nut to it.

source
- aaaaace@lemmy.blahaj.zone ⁨3⁩ ⁨months⁩ ago
  Also, G Flex is an epoxy formulated for plastics and West Systems has tutorials on their site.
  
  In this case, I’d drill a small hole in the center, put CA or epoxy in it, then screw another screw into the epoxied hole and let it set up.
  
  source
  - Brkdncr@lemmy.world ⁨3⁩ ⁨months⁩ ago
    There’s not need for all that work. Just a dab of epoxy or glue right on top, the any appropriate sized nut on top of that.
    
    Any drilling/dremel work just creates dust and metal shavings.
    
    source
Cooljimy84@lemmy.world ⁨3⁩ ⁨months⁩ ago
Depending how tight it is you could superglue something to it to turn it ?

source
- fernlike3923@sh.itjust.works ⁨3⁩ ⁨months⁩ ago
  I don’t really have superglue right now, and the screw looks like this far up, not sure it can be called tight or not.
  
  Image
  
  (Screwdriver for comparison, couldn’t really find something better.)
  
  source
  - Cooljimy84@lemmy.world ⁨3⁩ ⁨months⁩ ago
    You could also padding out the screwdriver tip or the screw hole. I’ve used sticky tape before, but again if its tight your pretty much out of luck…
    
    source
- A_Union_of_Kobolds@lemmy.world ⁨3⁩ ⁨months⁩ ago
  That would have to be a pretty loose screw
  
  source
- Broken_Monitor@lemmy.world ⁨3⁩ ⁨months⁩ ago
  Pretty much this - depending how much surface area and how good the glue is you might get it or you might snap that right off too. If it fails the next step is to carefully drill the screw out. A somewhat riskier operation but itll get it open
  
  source
linearchaos@lemmy.world ⁨3⁩ ⁨months⁩ ago
I prefer the rubber band trick first but usually when I get them down to this point I’ll use a smaller flathead from a jeweler set, see if you can find something that fits in between the two opposing tines of the Philips

source
LordWiggle@lemmy.world ⁨3⁩ ⁨months⁩ ago
I don’t know if any is small enough, but there is a tool for this if nothing else works. A damaged screw extractor.

source
- Revan343@lemmy.ca ⁨3⁩ ⁨months⁩ ago
  The square shaped oneswork best, common brand is Easy Out
  
  source
Live_your_lives@lemmy.world ⁨3⁩ ⁨months⁩ ago
It looks like you probably don’t have enough edge for this, but a simple vise grip could work.

source
- iconic_admin@lemmy.world ⁨3⁩ ⁨months⁩ ago
  This was my first thought also. The defcon 2 solution. If that doesn’t work, the next step is to drill it out.
  
  source
piecat@lemmy.world ⁨3⁩ ⁨months⁩ ago
A dab of super glue in the screw hole, find a screw driver you don’t really care about, add a drop of superglue accelerator

source
ace_garp@lemmy.world ⁨3⁩ ⁨months⁩ ago
Just unbutton it :P

source
Jackhammer_Joe@lemmy.world ⁨3⁩ ⁨months⁩ ago
Oooh man - you’re screwed!

source
Luci@lemmy.ca ⁨3⁩ ⁨months⁩ ago
Rubber band?

source
- fernlike3923@sh.itjust.works ⁨3⁩ ⁨months⁩ ago
  Tried to no avail.
  
  source
lobo@lemmy.world ⁨3⁩ ⁨months⁩ ago
I’ve had good success tapping stripped the screws loose with sometring sharp and a hammer

Not sure if you can get something small and strong enough, small punch or sacrificial screwdriver might work

Here is a video of what i mean

youtu.be/SXNAW96O_d8?si=cxJt59PKdEOQDuqV

source
mlg@lemmy.world ⁨3⁩ ⁨months⁩ ago
If its big enough, try the rubber band trick to get some grip.

If its a tiny electronic screw, you’ll have to very carefully coax it out with either some needle nose pliers by gripping the outside, or by using a slightly larger screwdriver head and ensuring it doesn’t spin (very tricky, easy to strip screw further, using rubber band here might also help).

If the case can handle it, you can use the larger head and give it some decent amount of pressure to make sure it doesn’t spin when you turn. Again be careful, because pushing too hard could break the case.

You might have to inch it fractions of a turn at a time to make sure it doesn’t break, so it’ll take a while before it becomes loose enough to spin out by hand.

source
un_aristocrate@jlai.lu ⁨3⁩ ⁨months⁩ ago
With a screw extractor, you’ll find one at any hardware store.

source
- fernlike3923@sh.itjust.works ⁨3⁩ ⁨months⁩ ago
  I will check out a hardware store in the morning, didn’t really know about those, thanks! Though is it a tiny bit possible to get this out in some kind of DIY way too?
  
  source
  - brap@lemmy.world ⁨3⁩ ⁨months⁩ ago
    An expendable torx driver makes for a good remover of screws like these.
    
    source
Persen@lemmy.world ⁨3⁩ ⁨months⁩ ago
Use pliers and try not to break anything.

source
alphacyberranger@sh.itjust.works ⁨3⁩ ⁨months⁩ ago
The same thing happened to me… Luckily it was one of screws on the outer edges of the thermal housing. HP’s screws are such dogshit that they get easily stripped. I tried everything from rubber band to superglue. Eventually I had to drilled the screw head away.

source
- SkyezOpen@lemmy.world ⁨3⁩ ⁨months⁩ ago
  It’s easier not to clean them. I throw down tin foil before I make paninis in my hp laptop, because THAT’S ALL THEY’RE FUCKING GOOD FOR.
  
  source
  - Persen@lemmy.world ⁨3⁩ ⁨months⁩ ago
    Well my HP 250 G5 still somewhat works. The touchpad has serious ghost-touch problems and the housing is falling apart from just 2 disassemblies.
    
    source
    -> View More Comments
Railison@aussie.zone ⁨3⁩ ⁨months⁩ ago
Use a piece of leather or some multiple sheets of masking tape

source
Tippon@lemmy.dbzer0.com ⁨3⁩ ⁨months⁩ ago
From the two photos you’ve posted, it looks like there’s a little bit of the grooves left in the top of the screw, but not enough for your screwdriver to grip.

Try the rubber band trick first, mainly because it doesn’t cost you anything other than a rubber band to try. The combination of the little bits of the grooves and the grip from the band might do it.

If it doesn’t, a sacrificial screwdriver might work. You basically need to file off the pointy tip of the screwdriver until it can reach what’s left of the grooves, and unscrew it with a bit of downward pressure.

Good luck 👍

source
flashily_ripcord590@lemmy.world ⁨3⁩ ⁨months⁩ ago
Amazon search for tiny screw extractor.

source
vxx@lemmy.world ⁨3⁩ ⁨months⁩ ago
Looks like a screwdriver with a slit and the right size might still be able to grab it.

source
werefreeatlast@lemmy.world ⁨3⁩ ⁨months⁩ ago
I think the answer is no.

source

-> View More Comments